ADVANTAGES:
Good chemical resistance
Excellent chemical property
Excellent flexibility
Recommend for exterior
APPLICATION AREAS:
It is widely used for outdoor furniture, architectural hardware, air-conditioners, bicycle frames, garage doors and signboard ect.
Architectural hardware, aluminum profile, spaying on the aluminum of the doors and windows
Road signs stake, auto industry
Traffic apparatus: the accessory or hoop of the automobile and motorcycle, bicycle body and road bar
House hold appliance: the outer cover of air conditioner and gas stove board
Family apparatus: the apparatus of garden, handrail and bar
Agricultural apparatus and wire poles
Steel racks; lighting equipments
APPLICATION SCHEDULE:
Applied by electrostatic spraying gun that can provide negative tension of 60-80kV
Curing Schedule: 200°C 10minutes
Optimal film thickness: 60-80μm
POWDER PROPERTIES:
Specific gravity: 1.25-1.75(depend on colors)
Particle size distribution(Laser Particle size analyser): Less than 5% above 100μm;50-65% above 32μm
Average particle size:35-45μm
8-12 square meters/kg, thickness 60μm(100% of the powder coating utilization rate)
GLOSS&TEXTURE&COLOR
Supper Matt(<10%), Matt(<20%),Sub-gloss(20%-50%),Semi-gloss(50-75%),Glossy(76%-85%),High gloss(>85%)
Wrinkle/Sanded/Netted/Crackle/Crocodile/Hammer/Woodgrain/Metallic/Pearl/Antique
RAL color, full color range is available
SUBSTRATES AND PRE-TREATMENT:
In order to obtain optimal anti-corrosion properties it is recommended to apply a chemical pretreatment prior to powder coating application
Ferrous metals(cold rolled steel, cast iron ect.):Iron or Zinc phosphation
Zinc surfaces(Galvanized steel, zinc alloy):Chromation or Zinc phophation
Aluminum alloys:Chromatation
STORAGE:
Should be stored under dry conditions with good ventilation at a temperature not exceeding 30°C
Storage period recommended should not exceed 6 months, in case exceeding 6 months without affecting their free flowing properties, the powder will still have optimal characteristics.
Should be protected from excessive heat, humidity, water and contamination with foreign materials such as powder, dust, dirt ect.
Any leftover powder should be kept in an appropriate area that is cool and dry. Do not expose to the air too long as the powder properties may deteriorate with the moisture.
We offer powder coating capabilities that include a wide spectrum of colors, thickness, textures, softness, edge coverage, flexibilities, machinabilities, smoothness and temperature ranges. Free samples are available.
5. Shelf life is six months when stored in dry conditions at 25ºC.
| Properties |
Test Method |
Result |
| 1. Specific gravity |
Calculated |
1.4±0.3 |
| 2. Impact Resistance |
ASTM D2794 |
100 inch. lbs, no remove |
| 3. Pencil Hard |
ASTM D3363 |
H |
| 4. 60 Degree Gloss |
ASTM D523 |
3° ±1% |
| 5. Salt Spray Resistance* |
ASTM B117 |
1000 hr |
| 6. Cross Hatch Adhesion* |
ASTM D3359 |
5B pass |
| 7. Humidity Resistance * |
ASTM D2247, 1000hr |
No Removed, no bubble |
| 8. UV exposure* |
ASTM G154(Cycle 1), 400hr |
Gloss retain >50% |
*Testing was performed on
Disclaimer: This product data sheet is based on our knowledge and on current laws. The data referring to powder properties, application data and physical tests is based on lab-based samples. The highest quality powder coating finish results from proper substrate surface preparation, appropriate pretreatment, effective rinse stages, proper powder coating application and sufficient temperature and dwell to ensure the powder coating is cured. Factors such as quality or cure condition of the substrate may have an effect on the use and application of the product. It remains the responsibility of the user to test thoroughly if the product is applicable for the intended use. It is always the responsibility of the user to take all necessary steps to fulfill the demands set out in the local rules and legislation. We are not liable for any application-technological advice.
Q1: Are you a factory or trading company?
A1: We are a factory manufacturing products for over 28 years in Jinhu, China.
Q2: Why should I use powder coatings?
A2: There are some advantages of powder coatings. For example, they are harmless to humans. In addition, they also have resource efficiency and reduction of environmental pollution. After being coating, it forms a lasting film to protect the surface of the items.
Q3: Why should I buy from you not from other suppliers?
A3: We have a professional group of R&D. According to our clients' preference, we can adjust the formula to change the color, luster, appearance, and even metal texture and special patterns. Besides, we offer complete services before and after your purchasing, including color proofing, technical analysis, application recommendations, and after-sales services.
Q4: How about the delivery date?
A4: The delivery date will be within 15 days.
Q5: Can you offer the sample of my ideal color?
A5: Yes, we are pleasure to do. Please contact us to get the information. Besides, we can provide some color cards you have ordered in the delivery.
Q6: If there is no my ideal color, what can you offer me?
A6: We have the color proofing service, if any demands, feel free to contact us.
If any other questions, please feel free to contact us. We are glad to respond.
Audited Supplier 
){kind=link}
){kind=link}