| Customization: | Available |
|---|---|
| CAS No.: | 00-00-0 |
| Formula: | 00-00-0 |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
Electrostatic tribo spray dry powder coating paint for metal appliance
Automobile fuel tank powder coating Description:CURING CONDITIONS
200 °C (work piece temperature), 10-15 minutes
Coating performance:
spray film thickness of normal products for the 60 ~ 80um. The results of the relevant tests are based on the requirements of the standard (or specific) of the substrate and pre-treatment under the premise may be with the customer before the actual treatment of the substrate to achieve the effect of different. And the test is obtained under laboratory conditions for reference only. Appearance Visual: close to the visual general refers to the natural light gloss visual: close to the visual or according to demand adjustment
Salt resistance: 500 hours of no change in the coating, cross-section single-sided corrosion <2mm. GB1771-91 Bondrite 1000 standard treatment iron plate, the coating thickness of 70um.
Wet heat resistance: 1000 hours, the film slightly lost light, <1 GB1740-79Bondrite 1000 standard treatment iron plate coating thickness 70um
Chemical resistance:
the general acid and alkali oil has a good resistance to normal temperature
AVERAGE COVERAGE
8-12 square meters / kg, thickness 60 microns (100% of the powder coating utilization rate)
PACKING
Outside carton lined with two layers of polyethylene bags, each containing 20 kg net weight.
STORAGE AND TRANSPORT
Stored in less than 30 °C, ventilated, dry, clean room, not near the fire source, heating, avoid direct sunlight, the product in the transport should be to prevent rain, sun, prolonged sun exposure.Storage products in line with the above conditions, since the date of production, effective storage period is 6 months.Over the storage period may be re-tested and the results were consistent with, can still be used.
HEALTH AND SAFETY
Coating powder is a non-toxic products, but should be avoided in the course of inhalation of dust.Proposed operators wear appropriate dust mask, glasses.If possible, try to avoid long-term skin contact with powder coating
|
Mechanical property |
||
|
Testing items |
Standards and methods |
Inspecting index |
|
Impact strength |
GB/T1732-1993, AS3715 2.8 |
>50kg/cm |
|
Bending resistance |
GB/T1185-88, AS1580 402.1, ISO9227 |
Pass 2-5 millimeters |
|
Adhesion CHECKED TEST |
GB/T9286-88,2mm Cross cut, ISO2409 |
Pass100/100, passes 0 levels |
|
Cupdrawing:Erichsen, ISO1520 |
Erichsen, ISO1520 |
Pass 3-7 millimeters |
|
Pencil hardness |
GB/T6739-86, Mitsubishi |
Pass H-2H |
|
Chemical resistance and weather resistance |
||
|
Salt spray test |
GB/T1771-91,500 hours |
The cross section of corrosion less than 2MM |
|
Hot and damp resistance test |
GB/T17740-79(89),1000 hours |
Without air bubbles, loses the light slightly |
|
Acid resistance |
10% CH3COOH, 240 hours |
Without air bubbles, the surface without damage |
|
Alkali resistance |
10% NaOH, 240 hours |
Without air bubbles, the surface without damage |
|
Heat resistance |
200degree,1 hour |
The color change is lower than E=1.5 |
|
Solvent resistance |
MEK24 hours soaked in solvent-free |
Without air bubbles, the surface without damage |
|
Uvioresistant |
QUV-313,500 hours |
Gloss higher than 80% lower than the Munsell color change level |
|
Water tolerance of |
2 hours |
No bubble, not falling, losing light |
We offer free samples to you.
Contact informatoin:
Danae Ren
You can check our picture of our sample panels as follows,
){kind=link}