| Customization: | Available |
|---|---|
| CAS No.: | 00-00-0 |
| Formula: | 00-00-0 |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
Steel Water/Petroleum Oil Pipe Anti Corrosion Pure Epoxy Powder Coating
Details:
This is an epoxy-based smooth satin coating with a high level of zinc, providing excellent corrosion protection while improving the adhesion properties of powder topcoats resulting in superior service life and film integrity. It is not recommended for exterior use without a topcoat,typically used for garden tools,industrial waste equipment,agricultural machinery, pipeline coatings, electrical switch gear,cabinets and cable ducting.
Quality Data Sheet:
|
Mechanical property |
||
|
Testing items |
Standards and methods |
Inspecting index |
|
Impact strength |
GB/T1732-1993, AS3715 2.8 |
>50kg/cm |
|
Bending resistance |
GB/T1185-88, AS1580 402.1, ISO9227 |
Pass 2-5 millimeters |
|
Adhesion CHECKED TEST |
GB/T9286-88,2mm Cross cut, ISO2409 |
Pass100/100, passes 0 levels |
|
Cupdrawing:Erichsen, ISO1520 |
Erichsen, ISO1520 |
Pass 3-7 millimeters |
|
Pencil hardness |
GB/T6739-86, Mitsubishi |
Pass H-2H |
|
Chemical resistance and weather resistance |
||
|
Salt spray test |
GB/T1771-91,500 hours |
The cross section of corrosion less than 2MM |
|
Hot and damp resistance test |
GB/T17740-79(89),1000 hours |
Without air bubbles, loses the light slightly |
|
Acid resistance |
10% CH3COOH, 240 hours |
Without air bubbles, the surface without damage |
|
Alkali resistance |
10% NaOH, 240 hours |
Without air bubbles, the surface without damage |
|
Heat resistance |
200degree,1 hour |
The color change is lower than E=1.5 |
|
Solvent resistance |
MEK24 hours soaked in solvent-free |
Without air bubbles, the surface without damage |
|
Uvioresistant |
QUV-313,500 hours |
Gloss higher than 80% lower than the Munsell color change level |
|
Water tolerance of |
2 hours |
No bubble, not falling, losing light |
Properties:
It is higher average specific gravity than standard powder coatings, therefore box feeders and
fluidizing hoppers will need to be tested to ensure adequate mixing. It may require increased air pressure
or vibration levels than standard powder coatings.
AVERAGE COVERAGE
8-12 square meters / kg, thickness 60 microns (100% of the powder coating utilization rate)
PACKING
Outside carton lined with two layers of polyethylene bags, each containing 20 kg or 25kg net weight.
GENERAL TYPES
Textures include sand grain, hammer, silk pattern, sand textured, marble,metallic, multi-color.
PHYSICAL PROPERTIES
CURING CONDITIONS
180 °C ~ 200 °C (work piece temperature), 10-15 minutes
STORAGE AND TRANSPORT
Stored in less than 30 °C, ventilated, dry, clean room, not near the fire source, heating, avoid direct sunlight, the product in the transport should be to prevent rain, sun, prolonged sun exposure.Storage products in line with the above conditions, since the date of production, effective storage period is 6 months.Over the storage period may be re-tested and the results were consistent with, can still be used.
HEALTH AND SAFETY
Coating powder is a non-toxic products, but should be avoided in the course of inhalation of dust.Proposed operators wear appropriate dust mask, glasses.If possible, try to avoid long-term skin contact with powder coating
We offer free samples to you.
You can contact me informatoin as follows,
){kind=link}